Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion
Home Forum Online Store Information LJ Webcam Gallery Register FAQ Community Calendar Today's Posts Search

Reply
 
Thread Tools Display Modes
Old 09-12-2010, 12:33 PM   #1
dgax65
Guerro Grande
 
dgax65's Avatar
 
Join Date: Jan 2006
Location: Houston, TX
Posts: 629
Most, if not all, fish finders have a low input voltage cutoff that will shut off the unit when the voltage is too low for NORMAL operation. My Lowrance 527 shuts off at 10.2 volts. If I recall, all of my Humminbird FF cut off at 10.3. They all work perfectly up until they reach the low voltage cutoff. I doubt it is a problem with power supply voltage. More likely is signal degradation caused by a bad connector or conductor. The first step is to check the transducer in the water. This will tell you several things:
1. If you get a good signal with the transducer in the water you know it was the mounting material/method and that the transducer, interconnecting cable and head unit are good.
2. If you still aren't getting any return on the display you will know that it wasn't the Goop.

If you determine that the fault does not lie with the mounting, then you need to check a few more things. See if you can connect another transducer to the head unit. If the other transducer works, then your transducer is bad and needs to be replaced. If you still don't get a signal then the problem is with the head unit or connectors. The most likely fault is corrosion on the connectors or a frayed/broken conductor. Corrosion on the pins of your transducer plug could cause diminished signal strength from the transducer, thus causing the depth reading to grow worse over time. Check the connectors on both the plug and head unit. The connectors on Humminbird units aren't really very watertight. Even a small amount of corrosion might cause some signal loss.

You can clean the connector pins with a weak acid solution. Use an acid brush to apply and gently clean the connectors. You must take care so as not to bend or break the pins. Use some electrical contact cleaner after to get rid of any residue. It is a very good idea to use a corrosion inhibitor on all electrical connectors on you kayak. In the past, I used a thin coating of dielectric grease on connectors. This will inhibit corrosion and also helps keep water out of the connectors. The downside is that it holds sand and dirt particles and if you use too much of the grease it can degrade the signal. Use sparingly and you'll be OK. I have since switched to Fluid Film for protecting my electrical connectors.

http://www.fluid-film.com/

You can get Fluid Film from Hook1 or the John Deere service center off I8 in El Cajon. Hook1 only has the cans of liquid Fluid Film. The John Deere place has it in aerosol cans.

You can get dielectric grease at West Marine or at many electronics and battery shops.
__________________
Douglas Gaxiola
Team No Fish- Amateur Staff
dgax65 is offline   Reply With Quote
Old 09-12-2010, 01:50 PM   #2
GregAndrew
Senior Member
 
Join Date: Mar 2009
Posts: 2,384
Great info there Doug. I had not heard about too much dielectric grease causing signal degradation. I have been using it very liberally, but have been having some problems with deeper water returns. I am gonna have to try a little less and see if it helps.
GregAndrew is offline   Reply With Quote
Old 09-20-2010, 07:13 PM   #3
Stan K G
Banned
 
Join Date: Sep 2010
Posts: 36
Got my wet mount setup, working great now.

Now I just need to figure out how the hell to read the FF without fish ID on
Stan K G is offline   Reply With Quote
Old 09-20-2010, 07:44 PM   #4
jbm
Member
 
Join Date: Jun 2010
Location: Escondido<->Carlsbad
Posts: 81
Just a bit more information on dielectric grease. It is not a conductor, it is an insulator. That's why you don't want to overdo it. You're still relying on the mechanical mating of the connector to create the conductive path. Dielectric grease is used because it will keep out water and oxygen but not short neighboring pins together in the connector.
jbm is offline   Reply With Quote
Old 09-21-2010, 11:04 AM   #5
Siebler
Senior Member
 
Siebler's Avatar
 
Join Date: Mar 2005
Location: Richland Oregon
Posts: 1,547
Quote:
Originally Posted by dgax65 View Post

You can get Fluid Film from Hook1 or the John Deere service center off I8 in El Cajon. Hook1 only has the cans of liquid Fluid Film. The John Deere place has it in aerosol cans.

You can get dielectric grease at West Marine or at many electronics and battery shops.
Or OEX, Thanks Doug......


Mission Bay is now a Fluid Film dealer and we will have it ins tock very soon (it already shipped from the warehouse in Norcal). We also carry the Dielectric Grease.
__________________
CJ Siebler


Siebler is offline   Reply With Quote
Old 09-21-2010, 11:58 AM   #6
cjthomas
Senior Member
 
cjthomas's Avatar
 
Join Date: Jun 2009
Posts: 108
dielectric grease

I was told to put a thin layer of dielectric grease on the female side and then plug in the connectors so that just the right amount of grease is applied to the pins.

Is this a good method to follow?
cjthomas is offline   Reply With Quote
Old 09-22-2010, 05:04 AM   #7
Jzo
Senior Member
 
Jzo's Avatar
 
Join Date: Aug 2010
Posts: 344
Quote:
Originally Posted by cjthomas View Post
I was told to put a thin layer of dielectric grease on the female side and then plug in the connectors so that just the right amount of grease is applied to the pins. Is this a good method to follow?
sounds like a good idea.
Jzo is offline   Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 10:24 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.