Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 03-04-2019, 07:44 AM   #1
MITCHELL
Sea Hunter
 
MITCHELL's Avatar
 
Join Date: Nov 2011
Location: Where ever I may roam where I lay my head I call home.
Posts: 2,228
Send a message via AIM to MITCHELL
Kraken-----

Anybody no where I can gets some blue welding rod.
Attached Images
File Type: jpg 20190304_074541.jpg (38.4 KB, 147 views)
File Type: jpg 20190304_082103.jpg (59.1 KB, 146 views)
File Type: jpg 20190304_082253.jpg (47.7 KB, 145 views)
File Type: jpg 20190304_083831.jpg (40.5 KB, 142 views)
__________________
Duke Mitchell

Last edited by MITCHELL; 03-04-2019 at 10:35 AM.
MITCHELL is offline   Reply With Quote
Old 03-04-2019, 08:43 AM   #2
MITCHELL
Sea Hunter
 
MITCHELL's Avatar
 
Join Date: Nov 2011
Location: Where ever I may roam where I lay my head I call home.
Posts: 2,228
Send a message via AIM to MITCHELL
Kraken

No more
Attached Images
File Type: jpg 20190304_094111.jpg (59.9 KB, 139 views)
__________________
Duke Mitchell

Last edited by MITCHELL; 03-04-2019 at 10:34 AM.
MITCHELL is offline   Reply With Quote
Old 03-05-2019, 08:19 AM   #3
kirkdavis
Senior Member
 
kirkdavis's Avatar
 
Join Date: Apr 2015
Location: SD County
Posts: 360
Patriotic

Now you have red white and blue. Go USA!
kirkdavis is offline   Reply With Quote
Old 03-05-2019, 12:23 PM   #4
MITCHELL
Sea Hunter
 
MITCHELL's Avatar
 
Join Date: Nov 2011
Location: Where ever I may roam where I lay my head I call home.
Posts: 2,228
Send a message via AIM to MITCHELL
Ya...

Buddy
Attached Images
File Type: jpg 20190120_143021.jpg (59.1 KB, 89 views)
__________________
Duke Mitchell
MITCHELL is offline   Reply With Quote
Old 03-05-2019, 07:58 PM   #5
Reiner
Member
 
Join Date: Apr 2016
Posts: 71
It's a fishing website. Keep your political BS to yourself and off the forum.
Reiner is offline   Reply With Quote
Old 03-06-2019, 04:11 AM   #6
MITCHELL
Sea Hunter
 
MITCHELL's Avatar
 
Join Date: Nov 2011
Location: Where ever I may roam where I lay my head I call home.
Posts: 2,228
Send a message via AIM to MITCHELL
Stay off my post....

Its called freedom....don't like what you see move along
__________________
Duke Mitchell
MITCHELL is offline   Reply With Quote
Old 03-06-2019, 04:42 AM   #7
Hunters Pa
Senior Member
 
Join Date: Jul 2006
Location: Fullerton
Posts: 1,357
I like the metal mesh reinforcement. What is the beige paste, glue? I have welded my share of cracks, but using a soldering iron and zip ties or trimmings from previous installs for material
Hunters Pa is offline   Reply With Quote
Old 03-06-2019, 05:00 AM   #8
MITCHELL
Sea Hunter
 
MITCHELL's Avatar
 
Join Date: Nov 2011
Location: Where ever I may roam where I lay my head I call home.
Posts: 2,228
Send a message via AIM to MITCHELL
It's a hobie plastic welder I got from Andy oex sunset beach

I don't no about any glue. But it works good, its was a cold day and I used a heat gun to. I have used harbor freight plastic welders and this works way better. It's best if you melt the mesh into kayak. There's no wasting of plastic rod. Holding plastic on the side does not work as well and takes for ever as apposed to pushing round rods down the center.
__________________
Duke Mitchell

Last edited by MITCHELL; 03-06-2019 at 05:05 AM.
MITCHELL is offline   Reply With Quote
Old 03-06-2019, 05:08 AM   #9
MITCHELL
Sea Hunter
 
MITCHELL's Avatar
 
Join Date: Nov 2011
Location: Where ever I may roam where I lay my head I call home.
Posts: 2,228
Send a message via AIM to MITCHELL
Zip ties is a good idea

Clear probably doesn't show as bad maybe ill see if they fit through the hole in my iron.
Before I got the hobie welder, I patched my canoe heating up a butter knife with a propane torch, and put mesh that got the job done to, it was like cauterization of a wound and flattened out some bumps.
__________________
Duke Mitchell

Last edited by MITCHELL; 03-06-2019 at 06:01 AM.
MITCHELL is offline   Reply With Quote
Old 03-06-2019, 07:28 AM   #10
Hunters Pa
Senior Member
 
Join Date: Jul 2006
Location: Fullerton
Posts: 1,357
Quote:
Originally Posted by MITCHELL View Post
Clear probably doesn't show as bad maybe ill see if they fit through the hole in my iron.
Before I got the hobie welder, I patched my canoe heating up a butter knife with a propane torch, and put mesh that got the job done to, it was like cauterization of a wound and flattened out some bumps.
Save any trimmings from installs of hatches or whatever. can also trim thin strips from inside underneath the hatch.
Hunters Pa is offline   Reply With Quote
Old 03-06-2019, 07:39 AM   #11
MITCHELL
Sea Hunter
 
MITCHELL's Avatar
 
Join Date: Nov 2011
Location: Where ever I may roam where I lay my head I call home.
Posts: 2,228
Send a message via AIM to MITCHELL
I have blue cut outs from my old Malibu double

It's thick and melts slow I thought about cutting it into strips I found my tin snips after I finished the job.
By the way best duck tape ever made is 622 shurtape I personally used to use it to mask new windows on building's. Put it on one time and take it off after finish. No glue residue from tape
__________________
Duke Mitchell

Last edited by MITCHELL; 03-06-2019 at 05:17 PM.
MITCHELL is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 11:21 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.