Kayak Fishing Adventures on Big Water’s Edge  

Go Back   Kayak Fishing Adventures on Big Water’s Edge > Kayak Fishing Forum - Message Board > General Kayak Fishing Discussion

Reply
 
Thread Tools Display Modes
Old 03-08-2009, 02:01 PM   #1
Jason
Member
 
Jason's Avatar
 
Join Date: Feb 2008
Location: Carlsbad
Posts: 80
Rigging a Trident 15 (Electronics)

I'm pretty stoked with how I have my Trident 15 rigged up and decided I would post up some pics and details of what I did. I didn't take the time to take pics of the process, just the end result. When I first bought this kayak, I searched all of the kayak fishing forums to get ideas on how I wanted to rig it up. I was really trying to keep it as clean and un-cluttered as possible and still have everything the way I wanted it. I used marine grade wiring, crimps and heat-shrink on all of the connections. I'm pretty confident this should last a long time without having to mess with it.

Bait Tank and Pump

I didn't have any reservations about putting holes in the bottom of the kayak, so I went thru-hull for the bait pump. This set-up has been rock solid for over a year now, with no leaks at all. That area does come out of the water in certain situations, but not enough to air-lock the pump or compromise the health of the bait.



This is how it is plumbed into the tank



The external hose for the bait tank is removable and gets stored inside the tank when I'm done.



Transducer

After using an in-hull transducer for over a year, I decided to switch it out for a thru-hull. I saw a couple of posts where guys had done this and that was all of the motivation I needed. I used just enough 5200 to get a good seal. I ended up trimming off the excess with an xacto knife. You can see the intake for the bait pump in the background.

This area of the hull had no signs of wear after over a year of use, so that's where I installed it.





I used the pool noodles to help secure the wires from bouncing around too much during transport.



You are not supposed to cut the transducer cable, so it had to go somewhere.



I'm very satisfied with the install and the performance of the thru-hull transducer. It's a major improvement over the in-hull. At this point in time, I have only been out on one eight hour trip and didn't take on one drop of water.

Power

This is what I'm using to power the Garmin 440s and the 500gph bait pump (the pump is on a 7/14 timer switch). It's a 12v-18ah battery that fit perfectly into this Pelican 1200 waterproof case. I have enough power to be on the water as long as I want.



Both the Garmin and the pump have their own fuses. I have been using this same battery set-up for over a year now with absolutely no signs of corrosion.



Here is how it looks on the outside.



This pic shows how it sits inside the kayak.



This is where I attach the wiring harness when the battery is removed. This keeps the connection from getting wet when I clean the inside of the kayak and keeps it secure during transport. I figure the less the wiring moves around the better.



This is what I did to keep the battery box in place. I bought a cheap Boogie Board from Walmart and cut it to fit, using the scuppers to help secure it. I wrapped the whole thing with duct tape, so in case it breaks it won't fall apart.



This is where it fits.





Plenty of room for rods and kill bag

In these next two pics, you can see that I still have plenty of room to store my rods and kill bag, without compromising the electrical rigging.

Looking back...



Looking forward...



That's at least 8' of room to store my gear for launching and landing in bigger surf. My jig stick is 8', so that works for me. I have yet to access the front hatch while on the water, everything fits through the Rod Pod.

Electronics

This is how the helm set-up looks while I'm fishing. The screen on the 440s is easy to see, even with my messed up eyes. Using the white background for the fishfinder makes it easier for me to see the detail. I'm using a Ram "Finger Grip" Mount to secure my VHF radio. I adjust the radio just high enough as not to interfere with the compass. I also carry a FRS radio to communicate with my fishing buds.



I usually keep my jig stick in the rod holder in front of me, when I'm not rigging up another rod. As of now I have a total of six rod holders, which seems sufficient for the three rods I currently use. I'm looking to add one or two more, to make room for another rod down the road.

In this pic, you can see the only external electrical connection, the power and transducer cable for the 440s. The 440s has an IPX7 waterproof rating, but still got the extended warranty from West Marine.



So that's it! My custom rigged Trident 15.

Jason
Jason is offline   Reply With Quote
Old 03-08-2009, 02:44 PM   #2
trob
Senior Member
 
trob's Avatar
 
Join Date: Mar 2007
Location: San Marcos (now idaho)
Posts: 231
Send a message via AIM to trob
really clean look. good job
__________________
trob is offline   Reply With Quote
Old 03-08-2009, 04:35 PM   #3
bellcon
Senior Member
 
bellcon's Avatar
 
Join Date: Jul 2007
Location: San Pedro
Posts: 999
Very nice fishing machine
great job on the custome work
bellcon is offline   Reply With Quote
Old 03-08-2009, 05:00 PM   #4
forefrazier
Senior Member
 
forefrazier's Avatar
 
Join Date: Jun 2008
Location: OC
Posts: 397
Very clean work Jason! Nice job.
forefrazier is offline   Reply With Quote
Old 03-08-2009, 05:50 PM   #5
Dan
Senior Member
 
Dan's Avatar
 
Join Date: Mar 2006
Posts: 1,053
tidy!
Dan is offline   Reply With Quote
Old 03-08-2009, 06:46 PM   #6
peguinpower
bing!
 
Join Date: Mar 2007
Location: socal
Posts: 246
That is great work you did there. Very impressed.

That transducer sure looks sweet.

/bing
peguinpower is offline   Reply With Quote
Old 03-08-2009, 08:05 PM   #7
JPSURF
Member
 
JPSURF's Avatar
 
Join Date: Mar 2007
Location: Long Beach, CA
Posts: 86
Very clean install!!!!

JP
JPSURF is offline   Reply With Quote
Old 03-09-2009, 08:28 AM   #8
Jason
Member
 
Jason's Avatar
 
Join Date: Feb 2008
Location: Carlsbad
Posts: 80
Thanks for the positive feedback guys.

Bing, I am able to get the double echos that you were asking about in your post. I was mostly fishing the squid grounds that day, with a 100 other boats . Lots of interference until I got away from the fleet. It seems that if I'm too close to other boats, with more powerful sounders, I get some interference. I was getting the interference with the in-hull as well. It looks like really thin dashed lines. Anybody else experience this?

Jason
Jason is offline   Reply With Quote
Old 03-09-2009, 10:37 AM   #9
linghunter
skunk
 
Join Date: Dec 2006
Posts: 61
Yes

I saw the same thing on my ff last time I was out. I believe you are familiar with the model I am using.

Paul
linghunter is offline   Reply With Quote
Old 03-09-2009, 08:54 PM   #10
peguinpower
bing!
 
Join Date: Mar 2007
Location: socal
Posts: 246
Quote:
Originally Posted by Jason View Post
Thanks for the positive feedback guys.

I get some interference. I was getting the interference with the in-hull as well. It looks like really thin dashed lines. Anybody else experience this?

Jason
Thanks for the follow up on the double bottom echo. The theory is, if you can see the echo, you see everything. Just limit the depth on the FF so you can cut the second bottom out of the picture.

As fer the interference, I got this with the gooped and the thru hull installation. I just bump up the Humminbird's NOISE cancellation when I'm next to boats or other yakkers.

Great job!

/bing
peguinpower is offline   Reply With Quote
Old 03-11-2009, 03:17 PM   #11
metalbob
King of Constipation
 
metalbob's Avatar
 
Join Date: Feb 2006
Location: North Park
Posts: 56
Man...that is clean! I cant wait to rig my next kayak, thanks for some Ideas

METALBOB
metalbob is offline   Reply With Quote
Old 03-11-2009, 04:40 PM   #12
Jason
Member
 
Jason's Avatar
 
Join Date: Feb 2008
Location: Carlsbad
Posts: 80
Quote:
Originally Posted by metalbob View Post

thanks for some Ideas...

METALBOB
That was the purpose of this post. Everything that I have done, has been done before... just modified a bit.
Jason is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 10:58 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.