|
|
|||||||
| Home | Forum | Online Store | Information | LJ Webcam | Gallery | Register | FAQ | Community | Calendar | Today's Posts | Search |
 |
|
|
Thread Tools | Display Modes |
04-02-2014, 11:21 PM
|
#1 |
|
Fish killer
Join Date: Jun 2008
Location: Surfside
Posts: 105
|
New battery box set up and xfactor rigging
This is the first thing today The new bright orange battery box 1 9ah 12v fishfinder/aux batt 1 12ah 6v bait pump Plan is to run 2 out lines to waterproof "trailer" plug disconnects so I can remove the box if needed. I also picked up the stuff to make my bait tank and also a bunch of Scotty parts and lastly a mark 4 hdi unit, I plan on changing to a elite 5hdi or better soon and move the mark 4 to the gfs yak |
|
|
|
04-04-2014, 11:10 PM
|
#2 |
|
Fish killer
Join Date: Jun 2008
Location: Surfside
Posts: 105
|
Haven't had much time to work on this but step 2 wire the box and keep it waterproof...
|
|
|
|
|
04-04-2014, 11:12 PM
|
#3 |
|
Fish killer
Join Date: Jun 2008
Location: Surfside
Posts: 105
|
Bait tank, fish finder and rod holders coming soon. Any input appriciated
Thanks! |
|
|
|
|
04-05-2014, 09:52 AM
|
#4 |
|
Member
Join Date: Aug 2013
Location: Pine Valley when not fishing La Jolla
Posts: 2,639
|
Are you going to install an on / off waterproof switch for the bait tank pump. On the battery box is the best place (keeps it most protected from the salt water). I have my battery box attached to the inside of the hull just to the side of the center hatch of my X Factor. It is held in place by 2 Velcro strips that are glued to the inside of the hull and the back of the battery box ( I used 3M weatherstrip cement), that keeps the box from sliding around, is still removable and does not take up room in the center hatch bag. Good luck on you project. Mark
__________________
MARK ......... 2016 MALIBU X FACTOR, 2020 SOLO SKIFF (Fishing Kayak on Steroids  )  
|
|
|
|
|
04-05-2014, 11:58 AM
|
#5 |
|
Member
Join Date: Jun 2013
Posts: 73
|
I have one 32 amps battery for my bait tank ff and bilge
And it seats inside the yak between the 2 square hatch |
|
|
|
|
04-18-2014, 04:29 PM
|
#6 |
|
Fish killer
Join Date: Jun 2008
Location: Surfside
Posts: 105
|
So finishing up my rigging, wiring up my bait tank
|
|
|
|
|
04-18-2014, 04:30 PM
|
#7 |
|
Fish killer
Join Date: Jun 2008
Location: Surfside
Posts: 105
|
Switch
|
|
|
|
|
04-18-2014, 05:46 PM
|
#8 |
|
Senior Member
Join Date: Mar 2011
Location: Santa Ana/Westminster
Posts: 1,256
|
whats the make and model of that orange box?
__________________
Kevin Yellow PA12 |
|
|
|
|
04-19-2014, 06:33 PM
|
#9 |
|
Member
Join Date: Jun 2013
Posts: 73
|
Your bait tank is too far back
I think Malibu have a tank that seat inside That slanted hatch And working with the suppers (drain & intake) |
|
|
|
|
04-19-2014, 07:05 PM
|
#10 |
|
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,943
|
I did something similar about 5 years ago with 2 6 volt, one in series 12 and 6 volt power
 http://www.bigwatersedge.com/bwevb/s...hlight=battery
__________________
 
|
|
|
|
|
04-19-2014, 07:15 PM
|
#11 |
|
Fish killer
Join Date: Jun 2008
Location: Surfside
Posts: 105
|
Man I wish I had those plugs on the box, what brand are those?
I can reach easier extended arm vs contorted twisted arm if its too close you know |
|
|
|
|
04-19-2014, 07:23 PM
|
#12 | |
|
Fish killer
Join Date: Jun 2008
Location: Surfside
Posts: 105
|
Quote:
|
|
|
|
|
|
04-19-2014, 08:36 PM
|
#13 |
|
Administrator
Join Date: Mar 2005
Location: 1-2 miles off the point
Posts: 6,943
|
Sea Dog deck connectors
__________________
|
|
|
|
|
|
|
Linear Mode
