![]() |
Quote:
. . . . . . . . . Borrow Georges paddle to measure it of course. Nice try George it's the thought that counts:D |
Quote:
I wanted to save this post for future reference...... |
Uh oh. Busted! :stupid::wink:
|
Ouch...that's gonna leave a mark.
Penalty! Let's see...28 X 5/8 X 22 X Y = 1,540 (Y = # of halis caught using measuring device) Deduct 1,540 posts from post count...:doh:...:D |
Quote:
EPIC FAIL!! Funny thing it that when I placed the measuring tape over it I noticed it but didn't think twice about it........its been a looooooong week. I'm off to bed for an hour than off to work!!! As usual.....glad I could entertain you guys. |
Quote:
|
Quote:
Ahahahahahhahhahhahah!!!!:luxhello: Good one jorge!!!! |
So using your "FUZZY" logic your 40 incher really measured out at 36.5 inches. I win!!!!!!!!
Now show us all how you calibrate your scale?:D:D:D |
Quote:
That's easy Matt, just get a ten pound basket and put your fish in it. :D |
Well I tried
http://www.youtube.com/watch?v=ZaUDEY6zRUU |
Quote:
|
Quote:
Why not use one long sticker and cut it where the paddle separates? Bring me your paddle......I'll hook you up with a sticker that is sure to get you so many legals you won't know what to do with all the fish. |
Transducer wet mount
Taking the example from Walrus, I wanted to take it one step furthur for the ease of filling it with water and to make it a little more secure.
The terminal box is from just about any DIY hardware store. I purchased all my materials from Marshals on 8423 Production Ave (at Miramar Rd). They have every bit of hardware you will need, from Termial box to stainless hardware and stainless/rubber washers. Purchase your terminal box so it is just big enough to hold your ducer. Accuracy in drilling the holes is crucial to maintaining a parallel ducer install, both left and right, and up and down so the ducer sits parallel to the bottom of your yak. I wanted an easy way to fill the ducer holder with water, so I drilled a hole in the sail mast. This enabled a refill at any time (although I have noticed "0" water loss). The terminal box sits right against the sail mast, so the mast also serves as something stable to secure the terminal box against. The initial results are great. I can following a jig all the way up/down past 100', and watch it as it sits there 10' above the bottom : ) . . . The ducer sitting in the terminal box http://www.bigwatersedge.com/bwegall...G_0864_640.jpg . . The sail mast removal http://www.bigwatersedge.com/bwegall...G_0868_640.jpg . . The install http://www.bigwatersedge.com/bwegall...G_0880_640.jpg . . The final product http://www.bigwatersedge.com/bwegall...G_0883_640.jpg . . |
Very clean
:cheers1: not sure it matters, but isn't your transducer in backwards now ? |
Quote:
*** Results may differ based on your Transducer *** *** I have a Lowrance *** Based on the techies over at Lowrance, the transducer I have is strictly 2D. It does not matter if I put it in as you would mount a Transom mount (facing to the back), or 180 degrees (backwards). As long as it is parallel to the bottom and sides, and you are shooting straight down, you will get a good picture and arches. |
Quote:
Thats what I thought, maybe the "front" is the front just because of the shape, to cut through the water when mounted on the transom? I guess with side imagining it may make a difference? right is left? On my trident I put it in as directed by Humminbird (front facing front) even though the knuckle heads at Ocean Kayak made the indention for the through supper backwards... http://www.momentoffame.com/photopos...m/IM000121.JPG |
Quote:
|
Regor, which Hobie are you on?
...and did you have to shape that terminal box at all to seal or does your yak have a nice flat spot it fits? |
Quote:
One of the reasons I installed the ducer as far back as possible (under the sail mast) is that it is somewhat flat there. I still had to do a little sanding on the sides of the terminal box, but none on the front or back of the box. The farther you move towards the front of the Revo, the hull gets steeper and steeper and requires more and more sanding to fit. IF I had a smaller ducer (other than the Lowrance), a smaller terminal box would probably have fit even further back under the sail mast, but the Lowrance is too big. BTW - I also did two sessions of goop. The second one was one day later, and it was just to make sure to fill in any possible air pockets that may have formed from the 1st goop session. The reason I did this - when I pulled my old Eagle ducer out of the direct goop to hull, I was shocked at the LARGE air pocket that had been riding under my ducer for the last year ! . . |
One way to avoid air bubbles is to put your tube of goop into a container of hot water for a few minutes. This thins the goop out allowing trapped air to escape. This method works best when using a foam retainer to hold the tranny.
|
All times are GMT -8. The time now is 02:03 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
© 2002 Big Water's Edge. All rights reserved.